10/100/1000M Ethernet media converter with DIP switch,support LFP and jumbo frame
Main features
Ø Supporting inter-conversion between 10/100/1000Base-TX and 1000Base-SX
Ø Supporting full-duplex and half-duplex and its auto-sensed
Ø Supporting automatic cross connection of twisted pair interfaces, facilitating system commissioning and installation
Ø Supporting the transmission of extra-long VLAN packets
Ø Supporting Quality of Service (QoS) and ensuring the transmission of VoIP packets
Ø Supporting STP to form a redundant network
Ø Supporting LFP function
FTechnical Indexes
| Parameter |
Specifications |
| Access mode |
10/100/1000Mbps Gigabit Ethernet |
| Standard |
IEEE802.3ab 1000Base-T , IEEE802.3z 1000Base-SX/LX Gigabit thernet,IEEE802.1qVLAN,IEEE802.1p QoS,IEEE802.1d Spanning Tree |
| Transmission distance |
Dual-fiber multi-mode: 220m (62.5/125μm)/550m (50/125μm)
Dual-fiber single-mode: 25/40/60/80Km
Single-fiber single-mode: 25/40/60Km
Category-5 twisted pair: 100m
|
| Port |
One RJ45 connector: connected to STP/UTP category-5 twisted pair
One fiber port: Multi-mode SC/FC/ST (fiber size: 50,62.5/125µm)
Single mode SC/FC/ST (fiber size: 9/125µm)
|
| Conversion means |
Media conversion |
| Delay |
<10us |
| BER |
<10-9 |
| MTBF |
100,000 hours |
| LED |
PWR (power supply), FX /ACT(optical link action), 1000M (twisted pair link1000M), 100M (twisted pair link 100M), TP/ACT (twisted pair packet forwarding) ,FDX (Full or half duplex status) |
| Power Supply |
AC110-220V to DC5V 1A |
| Power consumption |
5W |
| Operating temperature |
-10~55ºC |
| Operating humidity |
5%~90% |
| Maintaining temperature |
-40~70ºC |
| Maintaining humidity |
5% ~ 90% non-condensing |
| Dimensions |
26mm (H) * 70mm (W) * 94 mm (D) (external power supply) |
Explanation for LED indicator lamp
| LED indicator lamp |
status |
Explanation |
| PWR |
ON |
Power is ON. |
| OFF |
Power is Fail. |
| FX /ACT |
ON |
Fiber link is ok. |
| Blink |
Data is been received or transmitted |
| OFF |
Fiber link is fail. |
|
TP/ACT
|
ON |
Link is ok. |
| Blink |
Data is been received or transmitted |
| OFF |
Link is fail. |
| FDX |
ON |
Full duplex |
| OFF |
Half duplex |
| 100M |
ON |
Ethernet port 100M speed |
| 1000M |
ON |
Ethernet port 1000M speed |
FInstallation
1. Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with typical length of 100 meter. It features the function of automatically identifying the through line and cross wire
Fiber interface
SC/ST fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).
2. Connection
The network device (work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through twisted-pair. And the multi/single mode fiber is connected to SC/ST fiber interface of the optical transceiver. Then switch on. The corresponding LED is on for correct connection. (See the table below for the LED indicator lamp)
Product Tags:
|
|
10/100/1000M Ethernet Media Converter With DIP Switch , LFP And Jumbo Frame Images
|
